Derived from the granted resonator system of Helmholtz type and the RJ decompression system, the peripheral laminar decompression system constitutes an exceptional load of the driver in the very low frequencies improving speaker's braking, so transient rendering.
This system is similar in operation to the bass-reflex by the presence of two resonances framing an anti-resonance adjusted to the resonant frequency of the speaker in open air.
However the enormous progress made on the bass-reflex system is the coloring abscence (barrel's sonority) from 80 Hz to 300 Hz, by :
• Total acoustic filling of the enclosure increasing its apparant volume and avoiding all standing wave (coloring).
• The rear wave quickly exit the enclosure in phase with the front wave rolled through the cavity located immediately behind the speaker, this cavity acting as a low pass filter with very sharp cut (80 Hz to 30 dB per octave).
• The distortion obtained is extremely low compared to that obtained with a closed box.
• The cavity and its second baffle allows the rigorous phase of the tweeter with the boomer by spacial shifting from 3 to 5 cm (depending cutoff frequency).
1- Vent 2- Speaker
• Input impedance : 8 Ω
• Rated power : 80 W
• Sensitivity (for 1 W at 1 m) : 86 dB
• Amplitude frequency response curve : 100 to 35 000 Hz
• Bandwidth (±3 dB) : 150 to 30 000 Hz
• Cutoff frequencies : 2000 - 8000 Hz
- Tweeter : dome 19 mm ITT - LPKH90-19-145FK
Dôme Mylar
Aimant clos
Caractéristiques
Unités
Valeurs
Puissance nominale
W
30
Puissance maximale
W
50
Bande passante
Hz
4000-25000
Niveau d'efficacité caractéristique
dB
90
Diamètre nominal hors tout
mm
118
Diamètre bobine mobile
mm
19
Diamètre ouverture baffle
mm
75
Introduction dans l'entrefer
gauss
14500
Flux dans l'entrefer
Maxwells
-
Énergie magnétique du moteur
WS-1
-
Facteur de force
NA-1
-
Hauteur du bobinage
mm
-
Hauteur de l'entrefer
mm
-
Masse de l'aimant
g
-
Masse équipage mobile
g
-
Masse du haut parleur
g
400
Impédance nominale
Ω
8
Fréquence de résonance
Hz
1500
Facteur de qualité mécanique
Qms
-
Facteur de qualité électrique
Qes
-
Facteur de qualité total
Qts
-
Compliance de la suspension
10-3 MN-1
-
Température max de bobine mobile
C
-
- Midrange : dome 50 mm 3A - DS50
Caractéristiques
Unités
Valeurs
Puissance nominale
W
50
Puissance maximale
W
120
Bande passante
Hz
700-6000
Niveau d'efficacité caractéristique
dB
90
Diamètre nominal hors tout
mm
160
Diamètre bobine mobile
mm
50
Diamètre ouverture baffle
mm
125
Introduction dans l'entrefer
gauss
12 600
Flux dans l'entrefer
Maxwells
28 000
Énergie magnétique du moteur
WS-1
0,657
Facteur de force
NA-1
7,9
Hauteur du bobinage
mm
4
Hauteur de l'entrefer
mm
5
Masse de l'aimant
g
850
Masse équipage mobile
g
3,2
Masse du haut parleur
g
1 960
Impédance nominale
Ω
8
Fréquence de résonance
Hz
380
Facteur de qualité mécanique
Qms
5,1
Facteur de qualité électrique
Qes
1,7
Facteur de qualité total
Qts
0,57
Compliance de la suspension
10-3 MN-1
-
Température max de bobine mobile
C
180
- Lower midrange : cone 13 cm PHILIPS - AD7066-W8
Caractéristiques
Unités
Valeurs
Puissance nominale
W
40
Puissance maximale
W
-
Bande passante
Hz
60-3000
Niveau d'efficacité caractéristique
dB
87,6
Diamètre nominal hors tout
mm
166
Diamètre bobine mobile
mm
-
Diamètre ouverture baffle
mm
141
Introduction dans l'entrefer
gauss
-
Flux dans l'entrefer
Maxwells
-
Énergie magnétique du moteur
WS-1
-
Facteur de force
NA-1
6,714
Hauteur du bobinage
mm
-
Hauteur de l'entrefer
mm
-
Masse de l'aimant
g
-
Masse équipage mobile
g
12,2
Masse du haut parleur
g
1150
Impédance nominale
Ω
8
Fréquence de résonance
Hz
45
Facteur de qualité mécanique
Qms
2,8
Facteur de qualité électrique
Qes
0,54
Facteur de qualité total
Qts
0,453
Compliance de la suspension
10-3 MN-1
1,017
Température max de bobine mobile
C
-
• Dimensions (H x W x D) : 44 x 26 x 18 cm
• Unit weight : ? kg
Specially designed to operate like satellite with the slaved coffee tables TR500, TR800, TR1000 & TR1200.
Speaker « Phase Plus »
In this type of loudspeaker the drivers are all connected in the same polarity (the negative poles at the ground).
Music, like speech, is essentially a result of attacks, unbalanced signals, pulses, the drivers all working in the same direction operate in a consistent way when reproducing these signals.
The filter introducing a delay of the woofer relative to the midrange, and this one compared to the tweeter, it becomes necessary to shift the plans of the drivers to catch up acoustically this electrical phase shift. The acoustic shift corresponding varies with crossover frequency of the speakers and complexity of the filter. For example, if we chooses 500 Hz as the crossover frequency between boomer and midrange, the theoretical distance that must separating the speakers with a 6 dB per octave filter (one self and one capacitor) should be 17 cm ! With a 12 dB filter... 34 cm (it's far from the 3 to 5 cm provided in most loudspeakers...).
Moreover, this spatial shift must also consider the position of the acoustic center of each driver from its mounting plane.
The PHASE PLUS also optimizes the amplitude-frequency response of the loudspeaker, the drivers working then in phase around each cutoff frequency (pic. 2).
Conventional systems with little or no spatial shift, imposed to cross the polarities of successive drivers in order to regularize the amplitude-frequency response curve around their cutoff frequency. But this had the effect, firstly poor phasing when moving away from this cutoff frequency, the other unable to correctly reproduce transients (pic. 1).